Our TMZ Series Anchor Drill Rigs include three models: TMZ1095, TMZ1045 and TMZ-1250. Each model has a different configuration for geotechnical drilling and anchoring work. TMZ1045 features a split-type structure for drilling in restricted spaces such as basements, garages, culverts and small tunnels. TMZ-1250 supports 360° all-direction drilling for tunnel, culvert, subway and foundation pit projects. We offer all three models with a minimum order quantity of one unit.

 
 

1. TMZ Series Anchor Drill Rig Model Selection

The following table compares the three models by power, rotary performance, feed capacity, clamping range and machine dimensions.

Specification TMZ1095 TMZ1045 TMZ-1250
Rated power 55 + 37 + 2.2 kW 55 + 18.5 + 2.2 kW 119 kW @ 2,200 rpm
Crawler model LG-101 LG-101 LG-135
Travel motor Two-speed Two-speed —
Travel speed 1.8 / 3.3 km/h 1.8 / 3.3 km/h 1.4 km/h
Ground pressure 5.5 N/cm² 5.6 N/cm² 6.39 N/cm²
Gradeability 20° 20° —
Rotary speed 0–35 / 0–110 r/min 0–44 / 0–410 r/min 0–67 / 0–134 r/min
Maximum rotary torque 10,000 / 5,000 Nm 9,850 / 1,050 Nm 11,000 / 5,500 Nm
Impact energy 750 N·m — Approximately 550 Nm (listed as impact force)
Impact frequency 1,100 times/min — 0–1,150 times/min
Feed stroke 900–1,900 mm 1,200–2,200 mm 2,500 mm
Feed force 63 kN 45 kN 50 kN
Pull-up force 95 kN 45 kN 50 kN
Feed speed Not clearly specified 0–8.5 / 0–17 m/min 0–10 m/min; fast feed 0–50 m/min
Retraction speed Not clearly specified 0–8.5 / 0–17 m/min 0–10 m/min; fast retraction 0–50 m/min
Clamping range 60–210 mm 60–320 mm 60–210 mm
Maximum clamping force 310 kN 310 kN 212 kN
Machine dimensions 3,353 × 1,200 × 2,300 mm (rig) 3,353 × 1,200 × 2,544 mm (rig) 5,900 × 1,500 × 2,850 mm
Power station dimensions 3,200 × 1,200 × 2,000 mm 3,200 × 1,200 × 2,000 mm —
Weight 5.5 + 2.4 T 5.7 + 2.3 T 10,000 kg

2. TMZ Series Anchor Drilling Rig Configurations and Working Conditions

TMZ1095

TMZ1095 features a rotary-impact power head with two rotary speed ranges:

  • Low-speed range: 0–35 r/min, with 10,000 Nm torque.
  • High-speed range: 0–110 r/min, with 5,000 Nm torque.
  • Impact energy: 750 N·m.
  • Impact frequency: 1,100 times/min.
  • Feed stroke: 900–1,900 mm.
  • Feed force: 63 kN.
  • Pull-up force: 95 kN.
  • Clamping range: 60–210 mm, with a maximum clamping force of 310 kN.

The drilling rig measures 3,353 × 1,200 × 2,300 mm, and the power station measures 3,200 × 1,200 × 2,000 mm. Their listed weights are 5.5 T and 2.4 T respectively.

TMZ1045

TMZ1045 uses a split-type structure for drilling in restricted working spaces, including basements, garages, civil air defense projects, culverts and small tunnels.

Its stated drilling applications include:

  • Grouting holes
  • Anchor bolt holes
  • Steel pipe piles
  • High-pressure rotary jet grouting
  • Core drilling

Different drilling tasks can be accommodated through drill tool replacement and power-head adjustment. The machine can also be used for tunnel pipe-roof support holes, blasting holes and foundation grouting holes.

Key configuration details include:

  • High-speed rotary power head.
  • Low-speed rotary range: 0–44 r/min, with 9,850 Nm torque.
  • High-speed rotary range: 0–410 r/min, with 1,050 Nm torque.
  • Hydraulic motor and gearbox feed system.
  • Feed stroke: 1,200–2,200 mm.
  • Feed and retraction speeds: 0–8.5 / 0–17 m/min.
  • Feed and pull-up force: 45 kN.
  • Clamping range: 60–320 mm, with a maximum clamping force of 310 kN.

The drilling rig measures 3,353 × 1,200 × 2,544 mm, and the power station measures 3,200 × 1,200 × 2,000 mm. Their listed weights are 5.7 T and 2.3 T respectively.

TMZ-1250

TMZ-1250 is configured for drilling in tunnels, culverts, subway projects and relatively small foundation pits. Its stated working conditions include clay, sand and gravel, and moderately weathered rock or softer formations.

For hard-rock drilling, the machine can work with an air compressor and pneumatic down-the-hole hammer.

Its 360° all-direction rotation supports drilling toward the tunnel face, side walls and tunnel roof, as well as vertical drilling.

Key configuration details include:

  • Engine: DCEC QSB4.5-C160 III.
  • Rated output power: 119 kW @ 2,200 rpm.
  • Electrical system: 24 V.
  • Fuel tank capacity: 200 L.
  • Hydraulic oil tank capacity: 400 L.
  • Hydraulic circuit working pressures: 0–22 MPa, 0–22 MPa and 0–20 MPa.
  • Traction force: 65 kN.
  • Feed stroke: 2,500 mm.
  • Feed and pull-up force: 50 kN.
  • Feed speed: 0–10 m/min; fast feed: 0–50 m/min.
  • Retraction speed: 0–10 m/min; fast retraction: 0–50 m/min.
  • Rotary and impact operating modes.
  • Impact frequency: 0–1,150 times/min.
  • Impact force: approximately 550 Nm, as listed in the product specifications.

For rotary operation, the high-speed range is 0–134 r/min with maximum torque of 5,500 Nm, while the low-speed range is 0–67 r/min with maximum torque of 11,000 Nm.

The machine measures 5,900 × 1,500 × 2,850 mm and weighs 10,000 kg. Its crawler length is 2,450 mm, overall width is 1,500 mm and ground clearance is 300 mm.

For rotary jet grouting work, a dedicated operating handle allows adjustment of rotation speed and lifting speed.

3. TMZ Series Anchor Drill Rig Customization and Order Options

Customization is available for TMZ1095, TMZ1045 and TMZ-1250. The current product specifications do not list specific adjustable components or customized parameter ranges.

For TMZ1045, drill tools can be replaced and the power head adjusted for different drilling tasks. TMZ-1250 can work with an air compressor and pneumatic down-the-hole hammer for hard-rock drilling.

The minimum order quantity is one unit for each model.

4. Geotechnical Drilling Rig Manufacturing and Technical Support

We develop, manufacture and sell multifunctional fully hydraulic drilling rigs, including equipment for geotechnical drilling and anchoring applications.

For overseas customers, we provide:

  • 24-hour telephone technical support.
  • Remote technical guidance through video.
  • On-site service when an issue cannot be resolved remotely.

Our equipment has been supplied to overseas markets including Singapore, Vietnam, Russia, South Korea and the Middle East.

5. Request a TMZ Series Anchor Drill Rig Quotation

Send us your required model, drilling specifications, project conditions or equipment reference photos. You can also provide your required quantity when requesting a quotation for distribution or project procurement.

We will review your information and provide a quotation for the corresponding TMZ Series Anchor Drill Rig.

As one of the most professional tmz series anchor drill rigs manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please rest assured to wholesale durable tmz series anchor drill rigs made in China here from our factory. For price consultation, contact us.

Geotechnical Engineering Drilling Rig, Hydraulic Soil And Rock Anchoring Drill Rig, tmz series anchor drill rigs

(0/10)

clearall